A STEM Project: Coding in TurtleStitch - Tracing An Image in TurtleStitch Using A Design Created in Silhouette And Appliquéing a Portion of the Design

An Easter Basket and a Tea Towel Embroidered with my Bunny TurtleStitch Design

In my previous blog posting, I created a design in Silhouette, imported the SVG design into TurtleStitch and appliquéd the entire design.  In this blog posting, I will continue my journey but this time, only appliquéing a portion of the design and using a running stitch for the rest of the design.

My tracing program is a SNAP! program whereby simple keyboard commands are typed and the movement of the mouse is recorded in a graphic table of X and Y coordinates. These series of X and Y coordinates create the path that will be embroidered. My computer code had to be modified because only a portion of the design is going to be appliquéd.  I also wanted this code to be saved for the next Turtlestitch session.  I added another column in the array to indicate whether or not the X and Y Coordinate will be appliquéd.

I created my Easter bunny design using the Silhouette software and centered it on an 8 1/2 in. x 11 in. media page. 

Easter Bunny design in Silhouette

I determined that the maximum image size for the Turtlestitch stage area is approximately 3 1/2 inches in height x 4 1/2 inches in width. I resized the image in the Silhouette software to accommodate this TurtleStitch constraint. The image cannot be resized once it has been added to the stage area in Turtlestitch. (Once the design is traced, it can be resized using my TurtleStitch program.)  I then saved the image as an SVG using the Silhouette software.  (Please note that Designer Edition or higher is required to export SVG's in Silhouette.)   The image could be exported as a PNG or a JPEG file. However, the image was too small and blurry in TurtleStitch with the default parameters from the Silhouette program.

Here is my Easter Bunny SVG image. https://drive.google.com/file/d/1kPy43WH1V0C2O4hYFHfiZPQrjWyR2f3O/view?usp=sharing

Open my TurtleStitch  program https://www.turtlestitch.org/run#cloud:Username=Elaine&ProjectName=Traced%20and%20Appliquéd%20Easter%20Bunny

My tracing program is a SNAP! program whereby simple keyboard commands are typed and the movement of the mouse is recorded in a graphic table of X and Y coordinates. These series of X and Y coordinates create the path that will be embroidered.

Import my Easter bunny SVG as background to the stage area. 

I recommend tracing the image in an enlarged stage area. To enlarge the stage area, in the ribbon area above the stage, there is a box with two arrows pointing outwards.  Toggle this button to enlarge the stage area or to return to the original size with the palette and scripting pane.

Begin Tracing the Image

Press the "0" (zero) key to clear the "graphic" table. Move the cursor to where you want to start. Make sure that the appliqué command is toggled to green in the program. Press the "u" key to make a jump stitch to this location (I say the word "up" in my head as I do this to remember that the turtle(pen) should be in the "up" position as to not record the movement).  Press the space bar.  Make sure that there is a red line from the center of the design to where you are starting. The red line is a jump stitch. 

Press the letter "u" to move the mouse without drawing. To move multiple times without drawing. Press the letter "u" multiple times. Otherwise, press the space bar to continue drawing.  I placed the stitch points about an 1/8 inch apart. If the points are too close together, the design might not embroider successfully. If you do not like the last point that was traced, it can be removed with the "r" key.  Only the last point can be removed with the "r" key so be careful as to where you place your stitch points.

When you have finished tracing the portion of the design that will be appliquéd, toggle the appliqué variable to false.  Continue tracing the design. The rest of the design will then have a running stitch when embroidered.

Press the "a' key to view the appliquéd area and the running stitched design.

The "e" key MUST be pressed when the design is completed. Make sure you do this before exporting the design to be embroidered for your machine.  I did not do this and my Brother PE 800 machine would not load the exported design.

Export the design for your embroidery machine. Have fun appliquéing the design!

To retrieve the Easter bunny that was designed, press the "a" key. 

The block will be outlined in green when the command is executed and the Easter bunny design will be created in the stage area.  Export the design to your embroidery machine.

When the code is run on your embroidery machine, place a scrap of fabric for the egg appliqué. There are two stops coded in the design.  The first is so that the egg design can be trimmed. The second stop is after the satin stitch applique. This second stop is not really necessary but I did not remove it.( I coded it so that I could trim and redo any spots of the appliqué that did not look nice by manually working with my embroidery machine stitch points.)

I made a tea towel and an egg basket with the Easter Bunny design.

Here is a PDF of the design.  To make the Easter Bunny basket, print out the PDF.

https://drive.google.com/file/d/1b3c1PQlfeFFjO6uU6XZcpvhsijeUKY_t/view?usp=sharing

Trace the basket pattern on a piece of 12 in x 12 in. fabric. After tracing the pattern, find the center of each of the six sides and place a pencil mark.  This will be where the embroidery will be centered.

Float a piece of fabric where the egg will reside and tack it down with a running stitch using the embroidery pattern created in Turtlestitch.  The embroidery hoop can be removed from the machine but do NOT remove the embroidery hoop. Cut away the excess fabric. Return the hoop to the embroidery machine to appliqué and complete the design. Repeat for each of the six sides.

Cut the basket pattern. I added a seam allowance at the top of the design because one of my bunnies was not centered correctly. Adjust the pattern as necessary.

Sew each of the sides of the basket with a 1/4 in. seam allowance.

Cut out a lining and batting for the basket.  I quilted the lining material to the batting with a one inch pattern on my sewing machine.

Sew each of the sides of the lining with a 1/4 in. seam allowance.

Align the seams of the lining and the bunny design.  Pin them together at each seam.

Cut out an 1 1/2 in strip of fabric about a yard long.  Fold to make a bias tape.

Pin and sew the bias tape to the top edge of the basket to complete the basket.

I also made a tea towel to accompany the basket. The tea towel was cut from a 13 in. x 20 in. piece of fabric with each of the sides double folded over with a 1/2 in seam allowance. I sewed bias tape to the bottom end of the towel before sewing the side seams.